electricalroles.com.auJoin

What does a power systems engineer do in Australia?

Short answer

A power systems engineer models how the grid behaves. They run load flow, fault and disturbance studies, prove that new solar, wind and battery plant meets its performance standards, and hand validated PSS®E and PSCAD models to AEMO and network operators. Modelled median pay is about $137,100 a year.

Checked against 9 sources

Woman power systems engineer in a saffron blouse smiling on a solar farm with a laptop under her arm
Core work
Grid studies and connections
Key software
PSS®E and PSCAD/EMTDC
Entry
Accredited engineering degree
Modelled median
$137,100 a year (Australia)

What does the job involve day to day?

Most of the work happens in simulation software. You build models of the network and of the plant connecting to it. Then you run steady state load flow studies, and studies of how the system responds over time to faults and disturbances. The aim is to see how voltage, reactive power and frequency hold up across a range of operating conditions.

Employers range from transmission and distribution networks to consultancies, generator developers and government energy agencies. The NSW public service, for example, has advertised power system analysis engineer roles that run studies and give technical advice on the state's electricity system. Some network roles also cover SCADA and control systems, from field RTUs up to the energy management system.

How does a generator connect in the NEM?

This is where a lot of renewables work sits. A developer has to show AEMO and the network service provider that the plant can meet its proposed access standards. AEMO treats PSS®E models as critical to that assessment, and the applicant also submits a connection study report showing how the plant will meet those standards.

Models move through stages. R1 covers the period from financial commitment, after the connection agreement is signed, until the plant earns revenue after registration and commissioning. R2 is model data taken from testing on site after connection. R2 tests check things like reactive power capability and how the plant responds to active power set-point steps, then the engineer validates the model against the measured results.

AEMO expects the PSS®E and PSCAD/EMTDC models to give consistent responses for balanced events. Being fluent in both tools is the skill most employers look for in connection work.

What skills make a good power systems engineer?

You need solid theory in machines, protection, control systems and power electronics, because inverter-based plant behaves very differently from a spinning generator. You also need patience for detail. A model with the wrong controller settings or a poorly aggregated collector network will fail due diligence and hold up a large project.

Writing matters as much as maths. Study reports go to AEMO, network operators and investors, and they need to be clear enough to stand up to review. Engineers who have spent time on site during commissioning and R2 testing tend to build better models, because they have seen how the real plant responds.

Pay

Australia (modelled median)
$137,100
New South Wales
$138,000
Victoria
$135,200
Queensland
$135,600
South Australia
$129,400
Western Australia
$150,100
Northern Territory
$141,000
Australian Capital Territory
$149,400
Tasmania
$121,200

AUD a year, before tax. Figures are for electrical engineers generally, based on ABS Employee Earnings and Hours, May 2025, indexed to 2026. State figures are modelled, not official. For comparison, Power and Water Corporation in Darwin advertised a Band 3 professional power SCADA engineer role in 2026 at a salary of $141,242 to $167,642. Seniority, specialist connection study experience and employer type move pay the most. Refer to the Electrical Engineers salary guide for figures from live adverts.

What you need

  • Engineering degreeMost electrical engineering roles need a bachelor degree or higher. For registration in Queensland, the degree must be recognised under the Washington Accord, or assessed as equivalent.
  • Simulation softwareConnection work runs on PSS®E for the network-wide studies and PSCAD/EMTDC for detailed electromagnetic transient modelling. AEMO expects the two sets of models to agree.
  • RPEQ in QueenslandAnyone providing professional engineering services in or for Queensland must be a Registered Professional Engineer of Queensland. The alternatives are working under the direct supervision of an RPEQ or working only to a prescriptive standard.
  • RPEQ eligibilityYou need at least five years of relevant experience in the past ten years, with at least four of them after graduation. You also need an independent assessment by an approved assessment entity.
  • Victorian registrationProfessional electrical and electronic engineers in Victoria have had to be registered since 1 June 2023. Unregistered engineers can only work under the direct supervision of a registered engineer or to a prescriptive standard.

State by state

QueenslandThe Board of Professional Engineers of Queensland registers RPEQs. The Act also covers engineers based interstate or overseas who do work for Queensland projects.
VictoriaSince 1 June 2023, anyone providing professional electrical engineering services in Victoria must be registered under the Professional Engineers Registration Act 2019. Unregistered engineers must work under the direct supervision of a registered engineer or to a prescriptive standard.

How to get there

  1. Years 1-4Accredited electrical engineering degreeChoose power, machines, protection and control electives where you can.
  2. Years 1-3 after graduationGraduate roleJoin a network operator, consultancy or developer and learn load flow and fault studies under supervision.
  3. Years 2-5Connection and model workBuild and validate PSS®E and PSCAD models, write study reports and support R1 submissions and R2 testing.
  4. Year 5 onRegistrationApply for RPEQ once you have five years' relevant experience, with at least four after graduation. Register in Victoria if you work there.
  5. Year 6 onSenior or lead engineerLead studies, review other engineers' models and advise on network planning.

Open now on ElectricalRoles.com.au

See all →

Questions people ask

Is a power systems engineer the same as an electrical engineer?

It is a specialisation within electrical engineering. The ABS groups it with electrical engineers, who design and supervise systems for generating, distributing and controlling electric power.

What software do power systems engineers use?

For grid connection in the NEM, the main tools are PSS®E and PSCAD/EMTDC. AEMO needs PSS®E models to assess access standards, and it expects the PSS®E and PSCAD responses to match for balanced events.

What are R1 and R2 in grid connections?

R1 is the stage between financial commitment and revenue, covering registration and commissioning. R2 is model data taken from on-site testing after the plant connects, which is used to confirm the model matches the real plant.

Do I need to be registered to work as a power systems engineer?

In Queensland you need RPEQ registration unless you work under the direct supervision of an RPEQ or only to a prescriptive standard. Victoria has required professional electrical engineers to be registered since 1 June 2023.

How much does a power systems engineer earn?

Modelled ABS-based figures put the median for electrical engineers at about $137,100 a year nationally, and about $150,100 in Western Australia. A 2026 Power and Water professional engineering role in Darwin advertised a salary of $141,242 to $167,642.

Sources

  1. AEMO: Access Standard Assessment Guide
  2. AEMO: R2 Testing Guideline
  3. AEMO: R1 Investment Certainty
  4. AEMO: Dynamic Model Acceptance Test Guideline
  5. Board of Professional Engineers of Queensland: Become a RPEQ
  6. Engineers Australia: Electrical engineering registration in Victoria
  7. ABS: ANZSCO 2333 Electrical Engineers
  8. NT Government: Power and Water control system engineer job
  9. NSW Government: Power System Analysis Engineer job

Electrical Engineers jobs by city

Let employers come to you

Upload your CV and we build your profile from it. Employers contact you. Free for job seekers.

Create your profile
Free email alerts

Be the first to know.

New electrical jobs, employers and talent, straight to you as they go live. Stay in the loop.

Get the inside track →