electricalroles.com.auJoin

What is the Capstone test for electrical apprentices?

Short answer

The Capstone is the final assessment in an electrical apprenticeship. Your RTO runs it near the end of training to confirm you hold ERAC's 32 critical competencies for safe electrical work. Licensing bodies such as WA's Building and Energy need proof you passed it before they issue an electrician's licence.

Checked against 10 sources

Four young electrical apprentices in colourful shirts high-fiving outside a sunny training workshop
Who runs it
Your RTO, late in the apprenticeship
What it checks
ERAC's 32 critical competencies
Apprenticeship
48-month nominal term (Qld)
Victoria
LEA instead: 3 tests, 75% to pass

What is the Capstone assessment?

The Capstone is usually the last assessment you sit as an apprentice electrician. The Queensland Training Ombudsman describes it as a test built to show you have the knowledge and skills to do all electrical work safely. It sits on top of four years of trade school and on-the-job work. It does not replace either of them.

The content comes from the Electrical Regulatory Authorities Council (ERAC) list of essential performance capabilities. Your on-the-job record has to show you met all 66 essential capabilities. The Capstone then confirms the 32 items flagged as critical. WA's Building and Energy has described it as having written and practical parts, and as open book.

When do you sit it, and what is on it?

You sit it late in your apprenticeship, after the core installation units are done. In the Certificate III in Electrotechnology Electrician (UEE30820), WA's licence form ties the Capstone to two units: Design, install and verify compliance and functionality of general electrical installations, and UEECO0023 Participate in electrical work and competency development activities. Industrial electricians on the Certificate III in Engineering pathway complete MEM10025 Undertake a Capstone Assessment along with MEM17003.

Expect the work you have done on site: running consumer mains, sub-mains and final subcircuits, building switchboards, selecting cables and protection, the MEN earthing system, and testing and verification to the Wiring Rules. Queensland expects apprentices to have done this work on multi-phase commercial or industrial jobs before they reach the end.

What happens if you fail?

Your RTO runs the Capstone, so you retake it through the RTO. Until you pass, you do not get the licence. You keep working as an apprentice under supervision. In Queensland, broad supervision of an apprentice should only start after the Capstone is passed. In 2026 the Queensland regulator limited one disciplined worker to general supervision until they completed Capstone training. That shows how much weight it carries.

Victoria sets out clear resit rules for its own test, the LEA. Each of the three parts needs 75% or more. Score 41% to 74% on the theory or practical and you wait 14 days before another go. Any fail on the Safe Working Practice test also means a 14-day wait. Score 40% or lower, or make six or more attempts, and Energy Safe Victoria can make you do a review or a course before you sit it again.

How does it link to your licence?

The Capstone is what lets the regulator accept your qualification for an unrestricted licence. In WA, a completing apprentice applies to Building and Energy with their Certificate III. They also need an RTO letter or Record of Results from the last two years showing they passed the Capstone. In Queensland, your RTO sends the completion statement (ATF-012) straight to the Electrical Safety Office, and you lodge Form 10 within three years of finishing.

In NSW, NSW Fair Trading lists the 6077AC Capstone Assessment as a required part of one pathway for people holding superseded qualifications. In Victoria, apprentices sit the Licensed Electrician's Assessment run at approved venues. Energy Safe Victoria accepts the LEA or an interstate Capstone as evidence for technical supervisors.

Pay

Award apprentice, 1st year
$29,097
Award apprentice, 2nd year
$34,916
Award apprentice, 3rd year
$40,735
Award apprentice, 4th year (Capstone year)
$47,718
Apprentices and trainees, typical earnings
$29,100–47,700
Licensed, award minimum (grade 5)
$58,193

AUD a year, before tax. Award rows are the official weekly minimums from the Electrical, Electronic and Communications Contracting Award 2020 (MA000025), effective 1 July 2026, multiplied by 52. The typical range is the 25th to 75th percentile (median $37,800) from ABS Employee Earnings and Hours, May 2025, moved to 2026 with a wage index, so it is an estimate. Overtime, allowances and adult apprentice rates push real pay higher. Refer to the Apprentices & Trainees salary guide for figures from live adverts.

What you need

  • ApprenticeshipA full-time electrician apprenticeship has a 48-month nominal term in Queensland, with training from an RTO and work under licensed electricians.
  • QualificationCertificate III in Electrotechnology Electrician (UEE30820), or Certificate III in Engineering Industrial Electrician in WA, with the Capstone units completed.
  • On-the-job evidenceA record showing you met ERAC's 66 essential capabilities. WA wants this confirmed by your RTO and your employer.
  • Capstone passProof from your RTO that you passed the Capstone and covered ERAC's 32 critical competencies. WA accepts this only if it was issued in the last two years.
  • CPR (Queensland)The Electrical Safety Office needs you to confirm you have done resuscitation training in the last 12 months.
  • ID and police check (WA)Building and Energy wants proof of identity and a police check from the last three months.

State by state

Western AustraliaBuilding and Energy needs your Certificate III and an RTO letter or Record of Results from the last two years confirming the Capstone pass. Industrial electricians show MEM10025 and MEM17003.
QueenslandYou must use an approved Skills Assure Supplier RTO for training, including the Capstone. The RTO sends form ATF-012 to the Electrical Safety Office, and you lodge Form 10 if you finished within three years.
VictoriaApprentices sit Energy Safe Victoria's Licensed Electrician's Assessment: theory (2 h 15 min), Safe Working Practice (50 min) and practical (4 h). You need 75% or more in each, and an RTO authorisation letter before you book.
New South WalesNSW Fair Trading lists the 6077AC Capstone Assessment as a requirement in its pathway for applicants who hold superseded qualifications.

How to get there

  1. Year 1Sign on as an apprenticeStart a training contract with an employer and an approved RTO. In Queensland the RTO must be a Skills Assure Supplier.
  2. Years 1-4Build your on-the-job recordLog installation, switchboard and testing work so it covers ERAC's 66 essential capabilities.
  3. Years 3-4Finish the core installation unitsComplete the design, install and verify units your RTO needs before the final assessment.
  4. Late year 4Sit the Capstone (or LEA in Victoria)Your RTO assesses the 32 critical competencies. In Victoria, book the three LEA tests once your RTO authorises you.
  5. On completionApply for your licenceSend the regulator your completion evidence. WA needs it dated within two years. Queensland needs Form 10 within three years.

Open now on ElectricalRoles.com.au

See all →

Questions people ask

Is the Capstone the same as a licence exam?

In most states it is the final assessment inside your apprenticeship, and your RTO runs it. The regulator then uses your pass as evidence when it issues the licence. Victoria is different: apprentices sit Energy Safe Victoria's Licensed Electrician's Assessment at approved venues.

What does the Capstone test?

It confirms you hold the 32 critical competencies from ERAC's essential capabilities list. That means safe installation, switchboards, protection, earthing, and testing and verification to the Wiring Rules. WA's Building and Energy has described it as open book, with written and practical parts.

Can I get my licence without passing the Capstone?

No. WA's licence form needs RTO confirmation that you passed the Capstone. Queensland's completion statement from your RTO is what the Electrical Safety Office relies on. Until you pass, you keep working as a supervised apprentice.

What is the pass mark for Victoria's LEA?

You need 75% or higher in each of the three assessments. Score between 41% and 74% on the theory or practical and you wait 14 days before resitting. Score 40% or lower and Energy Safe Victoria can set conditions, such as a review or a course, before your next attempt.

Do industrial electricians sit a Capstone?

Yes, in WA. Apprentices on the Certificate III in Engineering Industrial Electrician pathway complete MEM10025 Undertake a Capstone Assessment and MEM17003. They need evidence of both from the last two years when they apply to Building and Energy.

Sources

  1. WA Building and Energy: electrician's licence on completion of apprenticeship
  2. WA Building and Energy: Form R016 electrician's licence (completion of apprenticeship)
  3. WA Building and Energy: Electrical Focus 20 (capstone assessment)
  4. Energy Safe Victoria: undertaking the Licensed Electrician's Assessment
  5. WorkSafe Queensland: completing apprentices
  6. WorkSafe Queensland: supervising electrical apprentices
  7. QTIS: Electrician UEE30820
  8. Queensland Training Ombudsman: training of electrical apprentices follow-up report
  9. NSW Fair Trading: electrical licences
  10. Fair Work Ombudsman: Electrical, Electronic and Communications Contracting Award 2020

Apprentices & Trainees jobs by city

Let employers come to you

Upload your CV and we build your profile from it. Employers contact you. Free for job seekers.

Create your profile
Free email alerts

Be the first to know.

New electrical jobs, employers and talent, straight to you as they go live. Stay in the loop.

Get the inside track →